Skip to content Skip to navigation Skip to footer
POLARIS GOVERNMENT & DEFENSE
HELP CENTER
02/12/2024

2024 RANGER XD 1500 Oil and Filter Change

Required Tools and Supplies

  • 17mm Socket
  • Ratchet
  • Torque Wrench
  • 2.5-Inch (64mm) Oil Filter Wrench
  • Funnel
  • PS-4 5W-50 4-Cycle Oil (part number 2876245)
  • Oil Filter (part number 2521728
  • Oil Pan
  • Eye Protection
  • Nitrile Gloves
  • Shop Rags

For information on tools, read the Tools and Fasteners Guide. Always wear safety glasses and nitrile gloves when servicing your Polaris RANGER.

The Full Synthetic Oil Change (part number 2890882) and Extreme Duty Oil Change (part number 2890883) kits include oil and a new oil filter. For optimal performance, always use Polaris-recommended fluids as described in your Owner’s Manual

To change the oil and filter on your RANGER XD 1500 follow these steps:

1. Park the vehicle on a flat, level surface and ensure it is in PARK.

2. Stop the engine and allow it to cool down. 

3. Remove the key from the ignition.

4. Place a drain pan under the engine crankcase. Tip: Placing a rag in the bottom of the drain pan will help to prevent the splashing of oil.

5. Clean the area around the oil drain plug.

6. Remove the drain plug using a 17mm socket and allow the oil to drain completely. Caution: Hot oil can cause burns to skin. Do not allow hot oil to contact skin.

7. Remove all cargo from the cargo box and raise the cargo box to its maximum raised position.

8. Place a rag under the oil filter to catch any spillage.

9. Using the 2.5-inch (64mm) oil filter wrench, turn it counterclockwise to remove the oil filter.

10. Using a clean dry cloth, clean the filter sealing surface on the engine crankcase.

11. Lubricate the O-ring on the new oil filter with a film of fresh engine oil. Check to make sure the O-ring is in good condition. A new oil filter is part number 2540086.

12. Install the new filter and rotate it clockwise by hand until the filter gasket contacts the sealing surface, then turn it an additional 3/4 turn.

13. Reinstall the engine oil drain plug. Torque to 16 ft-lbs (22 Nm). Notice: The sealing surfaces on the drain plug and crankcase should be clean and free of burrs, nicks or scratches.

14. Remove the oil dipstick and fill the engine with the recommended amount of engine oil. The capacity is 4.25 quarts (4.0 L).

15. Reinstall the dipstick.

16. Verify the transmission is still in PARK.

17. Start the engine and allow it to idle for 30 seconds.

18. Stop the engine and inspect for leaks. Wait at least 15 seconds before removing the dipstick.

19. Wipe any residual oil off the vehicle. 

20. Remove the dipstick and wipe with a clean shop towel.

21. Re-install the dipstick in a clockwise direction until snug. Notice: Make certain the dipstick is threaded all the way into the dipstick tube to keep the depth of the dipstick consistent.

22. Remove the dipstick and check the oil level.

23. Add the recommended oil as necessary to bring the oil level within the SAFE range on the dipstick. Do not overfill.

24. Reinstall the dipstick in a clockwise direction until snug.

25. Lower the cargo box. 

26. Dispose of the used oil and filter properly at your local recycling center.

27. Reset the oil life monitor. 

For more information, see your authorized Polaris Dealer. To find a dealer near you, use the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner’s Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

YouTube® is a registered trademark of Google LLC

Unless noted, trademarks are the property of Polaris Industries Inc.
© 2024 Polaris Industries Inc.